Car Jacks Explained: Types, Features and How to Use One Safely

A car jack is one of those tools you don’t think about until you need it, usually at the side of the road with a flat tire or in the driveway on the weekend you finally swap to winter wheels. Picking the right jack, and using it the right way, makes those jobs quicker and a lot safer. This guide covers the main types of automotive jacks, the features that matter, and the steps for lifting a car without taking chances.

The main types of car jacks

Scissor jacks

Most cars come with a scissor jack in the trunk. It’s a compact diamond-shaped frame that you raise by turning a screw with a crank handle. They’re light and easy to store, but slow, with a small base, and meant for occasional emergency tire changes.

Bottle jacks

A bottle jack is a hydraulic jack shaped like a short cylinder. You pump a handle and hydraulic fluid pushes a ram straight up. Bottle jacks can lift heavy loads for their size and are popular for trucks and SUVs with higher ground clearance. Their downside is a tall minimum height, so many won’t fit under a lower car, and their narrow base needs a firm, level surface.

Floor jacks

A floor jack, sometimes called a trolley jack, is a long, low hydraulic jack on wheels. You roll it under the car, position the saddle under a lifting point and pump the handle. They’re quick and stable, which makes them the usual home garage choice, but they’re too heavy and bulky for the trunk.

Hi-lift and specialty jacks

Off-road drivers sometimes carry tall mechanical jacks for high vehicles. There are also low-profile floor jacks for lowered sports cars, transmission jacks for repair shops and electric hydraulic jacks that draw power from the car’s 12V battery, so you don’t have to pump a handle.

Features to look for in a jack

  • Lifting capacity. Jacks are rated in tons. You only lift part of the car at a time, but it’s wise to choose a jack rated well above the weight you’ll be lifting, so check your vehicle’s curb weight in the owner’s manual or on the door jamb sticker.
  • Minimum and maximum height. The jack has to fit under your car’s lifting point when lowered and raise it high enough to get a fully inflated tire on and off. This matters most for low cars and tall trucks.
  • Saddle size and padding. The saddle is the cup that contacts the car. A wide, padded or rubber-topped saddle spreads the load and is less likely to damage pinch welds.
  • Build and stability. A wide base, solid wheels and a sturdy frame make a jack less likely to tip. Hydraulic jacks should lower smoothly and in a controlled way when you open the release valve.
  • Weight and storage. A floor jack that’s too heavy to move comfortably won’t get used. If you want something for the trunk, a compact hydraulic or scissor jack makes more sense.

If you’d rather not pump a handle, an electric hydraulic jack that connects to the car battery with clips is another option. Its listing gives a rating of up to 5 tons and a lift range of 155 to 450 mm, which suits most cars and SUVs, and it comes with a storage case. Like any jack, it’s for lifting only, so pair it with rated jack stands, which are sold separately at most auto parts stores.

How to use a car jack safely

  1. Park on firm, level ground. Concrete or asphalt is best. Avoid gravel, grass and slopes, which can let the jack sink or the car roll.
  2. Secure the car. Put an automatic in Park or a manual in gear, apply the parking brake and turn off the engine. Place wheel chocks or bricks against the wheel diagonally opposite the one you’re lifting.
  3. Find the correct lifting point. Your owner’s manual shows where the car can be lifted. Many cars have reinforced pinch welds behind the front wheels and ahead of the rear wheels, often marked with notches or arrows. Lifting on the floor pan, plastic trim or suspension arms can damage the car or let it slip.
  4. Loosen the wheel nuts first if you’re removing a wheel. Break them loose about a quarter turn while the tire is still on the ground, so the wheel doesn’t spin.
  5. Raise the car slowly. Watch the saddle as it makes contact to make sure it’s centered on the lifting point, then lift only as high as you need.
  6. Put jack stands under the car. Place them at the manufacturer’s support points and lower the car gently onto them. A jack is a lifting tool, not a holding tool; hydraulic seals can leak and jacks can shift.
  7. Never put any part of your body under a car held up only by a jack. If you’re working underneath, the car must be on properly rated stands, and give the car a firm shake before you go under to make sure it’s stable.
  8. Lower carefully. Raise the car slightly off the stands with the jack, remove the stands, then open the release valve slowly. Tighten the wheel nuts in a star pattern once the wheel is back on the ground, and check them again after a short drive.

A bright, hands-free light makes it much easier to see lifting points and stand positions, especially on winter evenings. A rechargeable magnetic work light that you can set down beside the wheel works well for this.

Jack care and storage

Store a hydraulic jack the way its manual recommends, check it for leaking fluid or a bent frame before each use, and keep the factory jack, wheel nut wrench and any locking wheel nut key together in the trunk.

A jack is one of the core tools in a home garage. For the rest of the basics, see our guide to automotive tools for your home garage. If you’re changing tires because the weather is turning, our portable tire inflator guide covers getting the pressure right afterward, and our winter car accessories list helps you get the rest of the car ready.

FAQ

What size jack do I need for my car?

Check your vehicle’s weight and choose a jack with a comfortable margin above the load you’ll be lifting. Also make sure it fits under your car when lowered and lifts high enough to clear the tire.

Can I use the jack that came with my car for regular maintenance?

The jack supplied with most cars is meant for emergency tire changes. For regular work, a floor jack and a pair of jack stands are safer and much easier to use.

Do I really need jack stands?

Yes, any time you’re doing more than changing a tire at the roadside. Never rely on a jack alone to hold a car while you work under it.

We run the NicheStuff store; some links in this post go to products we sell.

Top image: Bukk, public domain, via Wikimedia Commons.